The behavior of tillage tools with acute and obtuse lift angles
Resumen
An experimental investigation was conducted to study the trend of draft force against forward speed and working depth for a range of lift angles beyond acute angles for a simple plane tillage tool. The experiments were performed in an indoor soil bin facility equipped with a tool carriage and a soil preparation unit propelled by an integrated hydraulic power system. The system was also equipped with electronic instrumentation including an Extended Octagonal Ring Transducer (EORT) and a data logger. The factorial experiment (4×3×3) with three replications was used based on Randomized Complete Block Design (RCBD). The independent variables were lift angle of the blade (45, 70, 90 and 120°), forward speed (2, 4 and 6 km h-1) and working depth (10, 25 and 40 cm). The variance analysis for the draft force shows that all independent variables affect the draft force at 1% level of significance. The trend of the draft force against working depth and forward speed had almost a linear increase. However, the trend of the draft force against the lift angle is reversed for lift angles >90. This finding, conflicts with the results of analytical and numerical studies which extrapolate the results achieved for acute lift angles to obtuse lift angles and have not been reported experimentally.Descargas
Citas
Chi L, Kushwaha RL, 1990. A non-linear 3D finite element analysis of soil failure with tillage tools. J Terramechanics 27(4): 343-366. http://dx.doi.org/10.1016/0022-4898(90)90033-I
Davoudi S, Alimardani R, Keyhani A, Atarnejad R, 2008. A two dimensional finite element analysis of a plane tillage tool in soil using a non-linear elasto-plastic model. Am-Euras J Agric Environ Sci 3 (3): 498-505.
Fielke JM, 1996. Interaction of the cutting edge of tillage implements with soil. J Agr Eng Res 63 (1): 61-72. http://dx.doi.org/10.1006/jaer.1996.0008
Gebresenbet G, Jönssonm H, 1992. Performances of seed drill coulters in relation to speed, depth and rake angles. J Agr Eng Res 52: 121-145. http://dx.doi.org/10.1016/0021-8634(92)80055-W
Godwin RJ, 2007. A review of the effect of implement geometry on soil failure and implement forces. Soil Till Res 97 (2): 331-340. http://dx.doi.org/10.1016/j.still.2006.06.010
Godwin RJ, Spoor G, 1977. Soil failure with narrow tines. J Agr Eng Res 22: 213-228. http://dx.doi.org/10.1016/0021-8634(77)90044-0
Godwin RJ, O'Dogherty MJ, 2007. Integrated soil tillage force prediction models. J Terramechanics 44 (1): 3-14. http://dx.doi.org/10.1016/j.jterra.2006.01.001
Godwin RJ, O'Doghertya MJ, Saundersb C, Balafoutisa AT, 2007. A force prediction model for mouldboard ploughs incorporating the effects of soil characteristic properties, plough geometric factors and ploughing speed. Biosyst Eng 97: 117-129. http://dx.doi.org/10.1016/j.biosystemseng.2007.02.001
Gratton J, Chen Y, Tessier S, 2003. Design of a spring-loaded down force system for a no-till seed opener. Can Biosyst Eng 45: 229-239.
Mamman E, Oni KC, 2005. Draught performance of a range of model chisel furrows. Agric Eng Int: CIGR Ejournal, Vol. VII, Manuscript PM 05 003.
Manian R, Rao VR, Kathirvel K, 2000. Influence of operating and disk parameters on performance of disk tools. Agricultural Mechanization in Asia, Africa and Latin America 31 (2): 19-26.
Manuwa SI, Ademosun OC, 2007. Draught and soil disturbance of model tillage tines under varying soil parameters. Agric Eng Int: CIGR Ejournal, Vol. IX, Manuscript PM 06 016.
McKyes E, Ali OS, 1977. The cutting of soil by narrow blades. J Terramechanics 14 (2): 43-57. http://dx.doi.org/10.1016/0022-4898(77)90001-5
McKyes E, Desir FL, 1984. Prediction and field measurements of tillage tool draft forces and efficiency in cohesive soils. Soil Till Res 4 (5): 459-470. http://dx.doi.org/10.1016/0167-1987(84)90053-9
Montgomery DC, 1991. Design and analysis experiments, 3rd edition, John Wiley & Sons, NY.
Oni KC, Clark SJ, Johnson HW, 1992. The effects of design on the draught of undercut sweep tillage tools. Soil Till Res 22: 117-130. http://dx.doi.org/10.1016/0167-1987(92)90026-8
Payne PC, Tanner DW, 1959. The relationship between rake angle and the performance of simple cultivation implements. J Agr Eng Res 4 (4): 312-325.
Ruciņš Ā, Arvīds V, 2006. Impact of the share inclination angle on the plough body draft resistance. Zemdirbyste/Agriculture 93 (4): 166-179.
Shrestha DS, Sighn G, Gebresenbet G, 2001. Optimizing design parameters on a moldboard plough. J Agr Eng Res 78 (4): 377-389. http://dx.doi.org/10.1006/jaer.2000.0663
Soehne W, 1956. Einige Grundlagen für eine landtechnische Boden-mechanik. Grundlagen Landtechnik 7: 1-27.
Stafford JV, 1979. The performance of a rigid tine in relation to soil properties and speed. J Agr Eng Res 24 (1): 41-56. http://dx.doi.org/10.1016/0021-8634(79)90059-3
Swick WC, Perumpral JV, 1988. A model for predicting soil-tool interaction. J Terramechanics 25 (1): 43-56. http://dx.doi.org/10.1016/0022-4898(88)90061-4
Tong J, Moayad BZ, 2006. Effects of rake angle of chisel plough on soil cutting factors and power requirements: A computer simulation. Soil Till Res 88: 55-64. http://dx.doi.org/10.1016/j.still.2005.04.007
USDA, 1987. USDA textural classification study guide. Soil Conservation Service, United States Department of Agriculture, revised February 1987.
Zeng D, Yao Y, 1997. A dynamic model for soil cutting by blade and tine. J Terramechanics 37(4): 317-327.
© CSIC. Los originales publicados en las ediciones impresa y electrónica de esta Revista son propiedad del Consejo Superior de Investigaciones Científicas, siendo necesario citar la procedencia en cualquier reproducción parcial o total.
Salvo indicación contraria, todos los contenidos de la edición electrónica se distribuyen bajo una licencia de uso y distribución “Creative Commons Reconocimiento 4.0 Internacional ” (CC BY 4.0). Consulte la versión informativa y el texto legal de la licencia. Esta circunstancia ha de hacerse constar expresamente de esta forma cuando sea necesario.
No se autoriza el depósito en repositorios, páginas web personales o similares de cualquier otra versión distinta a la publicada por el editor.
